RTS TM-2000 Manual do Utilizador descarregar pdf (Página 28)

7.6 Power-Up and Indications

1. Turn on the Zeus power switch on the back panel.

2. Boot the computer and start Windows.

3. Zeus will take a few moments to power up, during

which, the STATUS indicator will be red. After a few

moments, the STATUS and POWER indicators

should be green to indicate normal operation.

☞

The System and Audio status indicators should also

be lit to indicate normal operation.

7.7 ZEUSedit Software Installation

1. Insert the ZEUSedit installation disk in the

computer’s floppy drive.

2. Run the setup.exe program on the disk. Follow the

on-screen instructions to install the software.

3. When the installation is finished, remove the

installation disk and store it in a safe place.

7.8 Starting ZEUSedit

1. Run the ZEUSedit program.

2. During startup, ZEUSedit will immediately attempt

to contact the intercom system. This may take up to

10 seconds.

3. If ZEUSedit cannot contact the intercom system, you

will see the message “Unable to contact an intercom,

entering file mode.” In this case, refer to

“Troubleshooting the Computer Connection”.

4. If ZEUSedit does connect, you will see the message

“ONLINE” in the lower-right corner of the screen.

You will also see the message “Uploading alphas” in

the lower-left corner of the screen. This means that

ZEUSedit is uploading the intercom system

configuration information from Zeus. This may take

a few moments.

☞

The ZEUSedit status indicator (third from left) will

be lit whenever Zeus is communicating with

ZEUSedit.

7.9 Troubleshooting the Computer

Connection

If ZEUSedit cannot connect to Zeus, the most likely cause

is that the COM port setting of ZEUSedit needs to be

changed. (We’ll assume that your cable is properly con-

nected and that the Zeus power is on and the front panel

STATUS indicator is green.) It’s not always easy to deter-

mine exactly how the COM ports are numbered on your

computer, so just try them all as follows:

1. In the Options menu, select Communications.

2. ZEUSedit should currently be set to COM1. Select

COM2, then click OK.

☞

Leave the baud rate set at 9600.

3. Now click the Go online button to try

and connect.

4. If ZEUSedit still cannot connect,

repeat the above steps, using the setting COM3. If

that doesn’t work, try COM4.

5. If none of the above settings work (and you are sure

the cable connections are correct and that Zeus is

powered on) you may have to make some changes in

your computer setup. Some possible causes are that

you are using multiple modems or have other serial

port devices connected which are using all of the

COM1 to COM4 settings. In this case, the solution

may involve removing one of these devices and/or

relocating it to some other COM port. For example, if

you have an external modem connected to the

computer, you could power down your computer and

try removing it temporarily. Then connect the Zeus

cable in its place and see if you can connect. Note

that it is beyond the scope of this manual to isolate

the problem in your particular computer, and if you

are not sure how to proceed yourself, you should

consult a computer specialist.

26 Getting Started, Zeus™ DSP Intercom Matrix

POWER

STATUS

RESET

1 8 16 24

System (leftmost) and Audio Status Indicators. Red = OK

1 8 16 24

ZEUSedit Status Indicator (Third from left). Red = ONLINE

1 2 ... 23 24 25 26 27 28 29 30 31 32 33 ... 36 37

Comentários a estes Manuais

Sem comentários

RTS TM-2000 Manual do Utilizador Página 28

Comentários a estes Manuais

Manuais e produtos relacionados com Sistemas de porteiro eletrónico RTS TM-2000